Cram Exam Notes 5 Cisco Certified Network Associate CCNA

51.Routing metrics used by IGRP:

Bandwidth, MTU, Reliability, Delay, and Load.

1. Bandwidth: This is represents the maximum throughput of a link.

2. MTU (Maximum Transmission Unit): This is the maximum message length that is acceptable to all links on the path. The larger MTU means faster transmission of packets.

3. Reliability: This is a measurement of reliability of a network link. It is assigned by the administrator or can be calculated by using protocol statistics.

4. Delay: This is affected by the band width and queuing delay.

5. Load: Load is based among many things, CPU usage, packets processed per sec.

52. The metric limit for link-state protocols is 65,533

53. Following are the possible solutions for preventing routing loops.

1. Split Horizon - based on the principle that it is not useful to send the information about a route back in the direction from which the information originally came.

2. Poison Reverse - A router that discovers an inaccessible route sets a table entry consistent state (infinite metric) while the network converges.

3. Hold-down Timers - Hold down timers prevent regular update messages from reinstating a route that has gone bad. Here, if a route fails, the router waits a certain amount of time before accepting any other routing information about that route.

4. Triggered Updates - Normally, new routing tables are sent to neighboring routers at regular intervals (IP RIP every 30 sec / and IPX RIP every 60 sec). A triggered update is an update sent immediately in response to some change in the routing table. Triggered updates along with Hold-down timers can be used effectively to counter routing loops.

54. IP RIP based networks send the complete routing table during update. The default update interval is 30 seconds. IGRP update packet is sent every 90 seconds by default.

55. For IGRP routing, you need to provide the AS (Autonomous System) number in the command. Routers need AS number to exchange routing information. Routers belonging to same AS exchange routing information. OSPF, and IGRP use AS numbers.

56. CDP stands for Cisco Discovery Protocol. This protocol is proprietary of Cisco. CDP runs SNAP (Sub network Access Protocol) at the Data Link Layer. Two Cisco devices running two different Network layer protocol can still communicate and learn about each other.

57. Show IP protocol: This command will show information on RIP timers including routing update timer (30sec default), hold-down timer (default 180sec). It also displays the number of seconds due for next update (this is fraction of update timer). This command also gives the network number for which IP RIP is enabled, Gateway, and the default metric.

1. Show IP route: This command will display the IP routing table entries. In addition, it displays the Gateway of last resort (if one is assigned). It also displays the codes used for various types of routes. Some of the important codes are:

C: directly connected;

S: Statically connected

I : IGRP

R : RIP

2. Show IP interface: This command shows you interface-wise information such as IP address assigned to each interface, whether the interface is up, MTU etc.

3. Debug IP RIP: Debug IP RIP will turn the RIP debugging ON. This will display a continuous list of routing updates as they are sent and received. This leads to lot of overhead, which is the reason that you use "undebug ip rip" to turn-off debugging as soon as you finish with debugging.

58. Cisco router boot configuration commands:

1. boot system - This is a global command that allows you to specify the source of the IOS software image to load. If you configure more than one source, attempts are made to load the IOS from the first command in the configuration to the last successively. If the first fails, the second boot command is used.

2. boot system rom - Loads IOS from ROM.

3. boot system flash - Loads the first file from flash memory.

4. boot system tftp <> - Loads IOS with a filename from a TFTP server.

Cram Exam Notes 4 Cisco Certified Network Associate CCNA

40. There are five different types of passwords:

1. ENABLE PASSWORD - A global command that restricts access to privileged exec mode. This is a non-encrypted password.

2. ENABLE SECRET - Assigns a one-way encryptographic secret password, available in versions 10.3 and up. This secret password is used instead of the enable password when it exists.

3. Virtual Terminal Password (vty password): The virtual terminal password is used for Telnet sessions into the router. The password can be changed at any time. It can be set up when you configure the router from the console. There can be five distinct passwords corresponding to each vty (vty0 to vty4) or there can be a single password for all vtys.

4. Auxiliary Password: Auxiliary password is used to set password to the auxiliary port. This port is used to access a router through a modem.

5. Console Password: Console password is used to set the console port password.

41. Internal memory components of a Cisco router:
. ROM (Read Only Memory); Memory containing micro-code for basic functions to start and maintain the router. ROM is not typically used after the IOS is loaded.

2. RAM/DRAM : stores the running configuration, routing tables, and packet buffers. Some routers, such as the 2500 series, run IOS from Flash, not RAM.

3. NVRAM (Non-Volatile Ram): Memory that does not lose information when power is lost. Stores the system’s configuration file and the configuration register. NVRAM uses a battery to maintain the data when power is turned off.

4. Flash Memory: Stores the compressed IOS (IOS stands for Cisco Internetwork Operating System) image. Flash memory is either EEPROM or PCMCIA card. Flash memory enables you to copy multiple versions of IOS software. This allows you to load a new level of the operating system in every router in your network and then, to upgrade the whole network to that version at an appropriate time.

42. While a packet travels through an Internetwork, it usually involves multiple hops. Note that the logical address (IP address) of source (that created the packet) and destination (final intended destination) remain constant, the hardware (Interface) addresses change with each hop.

43. Default administrative distances some important routing protocols are as below:

Route Source Default Distance

Directly connect Interface 0

Static Route 1

IGRP 100

RIP 120

Unknown 255

An administrative distance of 0 represents highest trustworthiness of the route.

An administrative distance of 255 represents the lowest trustworthiness of the route.

Routed and Routing protocols:

- Routing protocols job is to maintain routing tables and route packets appropriately. Examples of routing protocols are RIP, IGRP, EIGRP, OSPF. Routers can support multiple independent routing protocols and can update and maintain routing tables for each protocol independently.

- Routed protocols are used to transport user traffic from source node to destination node. Examples of routed protocols are IP, IPX, AppleTalk.

44. There are three ways a router learns how to forward a packet:

1. Static Routes - Configured by the administrator manually. The administrator must also update the table manually every time a change to the network takes place. Static routes are commonly used when routing from a network to a stub (a network with a single route) network.

The command is

ip route network mask address/interface [distance]

ex: ip route 165.44.34.0 255.255.255.0 165.44.56.5

Here, 165.44.34.0 is the destination network or subnet

255.255.255.0 is the subnet mask

165.44.56.5 is the default gateway.

2. Default Routes - The default route (gateway of last resort) is used when a route is not known or is infeasible. The command is

ip route 0.0.0.0 0.0.0.0 165.44.56.

The default gateway is set to 165.44.56.5

3. Dynamic Routes - In dynamic routing, the routing tables are automatically updated. Dynamic routing uses broadcasts and multicasts to communicate with other routers.

The commands to enable rip are:

router rip

network .

45. To enable the Cisco IOS to forward packets destined for obscure subnets of directly connected networks onto the best route, you use "ip classless" command.

46. There are broadly three types of routing protocols:

1. Distance Vector (Number of hops) - Distance vector routing determines the direction (vector) and distance to any link in the internetwork. Typically, the smaller the metric, the better the path. EX: Examples of distance vector protocols are RIP and IGRP. Distance vector routing is useful for smaller networks. The limitation is that any route which is greater than 15 hops is considered unreachable. Distance vector protocols listen to second hand information to learn routing tables whereas, Link state protocols build routing tables from first hand information. Routers with distance vector protocols send its entire routing table to each of its adjacent neighbors.

2. Link State Routing: Link State algorithms are also known as Shortest Path First (SPF) algorithms. SPF generates the exact topology of the entire network for route computation, by listening to the first hand information. Link State protocols take bandwidth into account using a cost metric. Link State protocols only send updates when a change occurs, which makes them more efficient for larger networks. Bandwidth and delay are the most widely used metrics when using Link-State protocols. EX: OSPF and NLSP.

Benefits of Link State protocols:

1. Allows for a larger scalable network

2. Reduces convergence time

3. Allows “supernetting”

3. Balanced Hybrid - Balanced Hybrid combines some aspects of Link State and Distance Vector routing protocols. Balanced Hybrid uses distance vectors with more accurate metrics to determine the best paths to destination networks. EX: EIGRP.

47. Distance vector protocol depends only on Hop count to determine the nearest next hop for forwarding a packet. One obvious disadvantage is that, if you have a destination connected through two hops via T1 lines, and if the same destination is also connected through a single hop through a 64KBPS line, RIP assumes that the link through 64KBPS is the best path!

48. RIP (and IGRP) always summarizes routing information by major network numbers. This is called classfull routing.

49. Convergence is the term used to describe the state at which all the internetworking devices, running any specific routing protocol, are having identical information about the internetwork in their routing tables. The time it takes to arrive at identical information of the internetwork is called Convergence Time.

50. RIP,RIP2, and IGRP use distance vector algorithms.

RIP2 transmits the subnet mask with each route. This feature allows VLSM (Variable Length Subnet Masks) by passing the mask along with each route so that the subnet is

Cram Exam Notes 3 Cisco Certified Network Associate CCNA

31. Ethernet_II has a type field to identify the upper-layer protocol. 802.3 has only a length field and can't identify the upper-layer protocol.

32.To find valid hosts given an IP address (say 156.16.3.52) and a subnet mask (sat a 12-bit subnet). The valid hosts are determined as below:

A 12-bit subnet mask gives us 255.255.255.240; 4094 subnets, each with 14 hosts. (Host addresses of all zeros and all 1s can't be assigned). The 156.16.3.52 is in the 48 subnet range. The valid range is through 49 - 62. 63 is a broadcast address.

Here is how you get the subnet range:

1. Find the subnet mask. In this case, default subnet mask for Class B address is 255.255.0.0. There are additional; 12 bits in the subnet mask. Now the subnet mask looks like:

11111111.11111111.11111111.11110000. This is equal to 255.255.255.240.0.

2. Now, deduct the lowest value octet (Which is non zero), from 256. Here, (256-240)=16.

This is the value that the subnets are incremented. Therefore, you will have hosts with values from:

156.16.3.1 to 156.16.3.14 (All 0s and all 1s host addresses can not be used)

156.16.3.17 to 156.16.3.30

156.16.3.33 to 156.16.3.46

156.16.3.49 to 156.16.3.62 and so on.

It is important to know that subnets are incrementing here by a factor of 16.

33. The following are some important commands that can be used to edit and review command history buffer on a Cisco router. It will be useful to practice these commands.

A : Move to the beginning of the command line

E : Move to the end of the command line

F : Move forward one character, same as using "Right Arrow".

B : Move backward one character, same as using "Left Arrow".

P : Repeat Previous command, same as using "Up Arrow".

N : Repeat Next (more recent) command, same as using "Down Arrow".

B : Moves to beginning of previous word.

F : Moves to beginning of next word.

R : Creates new command prompt, followed by all the characters typed at the last one.

34. The following are some frequently used COPY commands:

1. COPY RUNNING-CONFIGURATION STARTUP-CONFIGURATION (alternatively, you can use an older version of the command, WRITE MEMORY): This command saves the current configuration to NVRAM. Alternatively, we can issue the command using short form: COPY RUNNING STARTUP - Copies configuration from RAM to NVRAM
2. COPY STARTUP RUNNING - This command merges configuration from NVRAM to RAM.
3. COPY FLASH TFTP - Copies current IOS from router flash memory to TFTP server.
4. COPY TFTP FLASH - Copies image file from TFTP server to flash. This is used to upgrade the IOS image file to a newer version, or if your IOS image becomes corrupt.

35. The banner is displayed whenever anyone logs in to your Cisco router. The syntax is

- "banner motd # " . MOTD stands for "Message Of The Day".

# symbol signifies the start of the banner message to the router. You will be prompted for the message to be displayed. You need to enter "#" symbol at the end of the message, signifying that the message has ended.

36. Router modes of operation:

1. User EXEC mode (Prompt: Router>):- This is the LOWEST level of access. This allows examination of router status, see routing tables, and do some diagnostics. However, you cannot change the router configuration, view the configuration files, or control the router in any way. The prompt in this mode is "Router>".

2. Privileged (enable) EXEC mode (Prompt: Router#):- This mode allows you to have all the privileges of EXEC (user) mode plus commands that enable you to view configuration files, change the router configuration, perform troubleshooting that could potentially disrupt traffic. The default prompt for this mode is "Router#".When you are working in the privileged mode (at # prompt), you can get back to user mode by typing "disable" at the "#" prompt.

3. Global Configuration mode (Prompt: Router (Config)#):-

Global configuration mode allows you to perform tasks that affect the entire router, such as naming the router, configuration of banner messages, enabling routed protocols, and generally anything that affects the operation of the entire router.

When you first switch on a router, you enter Setup mode. Setup mode is different from configuration mode in that setup mode appears when there is no configuration file present. Upon entering setup mode, you can supply some basic configuration parameters to Cisco router.

37. You can use "tab" to complete the command that you are typing.

38. SHOW command is extensively used for seeing the status and configuration information of the router.

Some of the frequently used commands are:

1. SHOW RUNNING-CONFIGURATION -This command displays the router's active configuration file, passwords, system name, and interface settings, interfaces IP addresses etc.

2. SHOW INTERFACE - Shows status and configuration information of the local interfaces. The first line says something like “TokenRing1 is up, line protocol is up”. The first part “TokenRing1 is up” describes the physical layer components such as electrical cabling and signaling are OK. The second part “line protocol is up” means that the router is detecting keep-alive messages. The router may be put into administratively down status, at which point the line would read, “TokenRing1 is administratively down, line protocol is down.”

3. SHOW INTERFACE SERIAL 0 - Shows the serial 0 configuration.

4. SHOW INTERFACES - Displays statistics for all interfaces configured on the switch.

5. SHOW PROCESS - Displays a router’s CPU utilization.

6. SHOW CONFIG - Displays information on the startup configuration.

7. SHOW VERSION - Displays information about the system hardware (RAM/ROM), software version, names of configuration files, and boot-images. This command will also show the current configuration register value.

39. The Cisco router can be configured from many locations.

1. Console port: During the initial installation, you configure the router from a console terminal connected to the "Console port" of the router.

2. Virtual Terminals (vty): A virtual terminal (vty) is typically accessed through Telnet. A router can be accessed through vty after it the initial installation in the network. There are five virtual terminals, namely, vty0,vty1,vty2,vty3,vty4.

3. Auxiliary Port: you can configure a router through auxiliary port. Typically, a modem is used to configure the modem through aux port.

4. TFTP Server: Configuration information can be downloaded from a TFTP server over the network.

5. NMS (Network Management Station): You can also manage router configuration through NMS such as CiscoWorks or HP OpenView.

40. There are five different types of passwords:

1. ENABLE PASSWORD - A global command that restricts access to privileged exec mode. This is a non-encrypted password.

2. ENABLE SECRET - Assigns a one-way encryptographic secret password, available in versions 10.3 and up. This secret password is used instead of the enable password when it exists.

3. Virtual Terminal Password (vty password): The virtual terminal password is used for Telnet sessions into the router. The password can be changed at any time. It can be set up when you configure the router from the console. There can be five distinct passwords corresponding to each vty (vty0 to vty4) or there can be a single password for all vtys.

4. Auxiliary Password: Auxiliary password is used to set password to the auxiliary port. This port is used to access a router through a modem.

5. Console Password: Console password is used to set the console port password.

Cram Exam Notes Cisco Certified Network Associate CCNA

About CCNA Exam: CCNA Certification is offered by Cisco®. CCNA tests your knowledge and skills in the areas of simple LAN/WAN switching, Cisco IOS, and routing technologies. Topics include TCP/IP model of internetworking, configuring, and troubleshooting RIP, RIP v2, IGRP, EIGRP, OSPF, NAT, Remote Access using some of the most widely used Cisco switches and routers. Please visit the Cisco website for current objectives. Two recommended resources for Cisco certification preparation are Cisco Press "Cisco CCNA Preparation Library" and CCNA by Sybex. There are many others that are very good, but not widely known. CCNA is the foundation exam for CCNP (Cisco Certified Networking Professional). The exam notes is a brief review of important points that help in quick review of key points.

Cram Notes:
1. Internetwork IP addressing:

IP addresses are written using decimal numbers separated by decimal points. This is called dotted decimal notation of expressing IP addresses.

The different classes of IP addresses is as below:

Class	Format	Leading Bit pattern	Network address Range	Maximum networks	Maximum hosts/ nodes
A	N.H.H.H	0	0-126	127	16,777,214
B	N.N.H.H	10	128-191	16,384	65,534
C	N.N.N.H	110	192-223	2,097,152	254

- Network address of all zeros means "This network or segment".

- Network address of all 1s means " all networks", same as hexadecimal of all Fs.

- Network number 127 is reserved for loop-back tests.

- Host (Node) address of all zeros mean "This Host (Node)".

- Host (Node) address of all 1s mean "all Hosts (Nodes) " on the specified network.

2. The range of numbers from 224.0.0.0 to 239.255.255.255 are used for multicast packets. This is known as Class D address range.
3. Subnetting is nothing but creating networks within a network. Subnetting allows an organization with a single IP address (Class A /ClassB /ClassC) to have multiple subnetworks, thus allowing several physical networks within the organization.

4. How to maximize the number of subnets for a given number of hosts:

Let us take a network ID of 168.8.0.0, and find the maximum number of possible subnets and the corresponding subnet mask that can accommodate at least 500 hosts. The steps involved are outlined below:

I. Find the Class of the IP address, in this case it is a class B network. Class B network has the form N.N.H.H. Therefore, we have a total of 16 bits (two octets) for assigning to internal networks and hosts. The minimum number of host addresses required is 500. The last octet corresponds to 2^8 = 256 hosts which is still less than 500 Hosts.. Therefore, you have to borrow one more bit from the third octet to make it 256*2 = 512 Hosts. This leaves 7 bits in the third octet for assigning subnet addresses. This is equal to 2^7=128 subnets.

II. Write the 7 bits available for subnetting in third octet in the form 11111110 (last bit being the Host bit). The decimal equivalent of the first seven bits is 2^7+2^6+2^5+2^4+2^3+2^2+2^1

= 128 + 64 +32 + 16 + 8 + 4 + 2 = 254.

III. Therefore, the subnet mask required is 255.255.254.0.

6. How to maximize the number of hosts for a given number of subnets:

Determining the subnet mask that allows maximum number of hosts:

Let us consider an IP address 196.202.56.0 with four subnets and maximize the number of host for the given subnets. The steps involved are as below:

I. The number of subnets required are four. We need to add subnets of all ones and all zeros to this. This is because all zeros and all ones subnets belong to "this subnet" and "all subnets" broadcasts and can not be used. Therefore, the total number of subnets to be reserved is 4+2 = 6.

II. We want to implement maximum possible Hosts. Therefore, we need to minimize the number of subnets. This minimum number is 6 here. If we reserve 2 bits, it results in only 2^2=4 subnets which is less than 6. Therefore, we have to reserve 3 bits for implementing subnets, resulting in 2^3=8 subnets. This is now optimized for maximum number of Hosts (as we have optimized for minimum number of subnets).

III. Write the 3 bits available for subnetting in fourth octet in the form 11100000 (Five 0s being Host bits). The decimal equivalent is 2^7+2^6+2^5

= 128 + 64 +32 = 224.

IV. Therefore, the subnet mask required is 255.255.255.224.

7. 127.0.0.1 is the local loop back address.

8. In an internetwork, the number of distinct IPs' required are

1. One each per client computer

2. One each per server computer

3. One each per router interface.

For example, your network has 2 servers, 26 clients machines, and 2 router interfaces the total number of IP addresses required are 30.

9. Finding the number of Hosts and subnets available for a given subnet mask: For example, let us find the number of hosts and subnets available for an IP 156.233.42.56 with a subnet mask of 7 bits.

a. Class B network has the form N.N.H.H, the default subnet mask is 16 bits long. There is additional subnet mask of 7 bits long.

b. 7 bits of subnet mask corresponds to (2^7-2)=128-2 = 126 subnets.

c. 9 bits (16-7) of host addresses corresponds to (2^9-2)=512-2 = 510 hosts.

Some times, the subnet mask is specified with the bits available in the default subnet mask. In this case the bits available in default subnet mask is 16. Therefore, total number of bits available in the subnet mask are 16+7=23. If you are given a subnet mask of 23 bits long for a class B address, it is understood that it contains the bits from the default subnet mask as well.

Hence, 126 subnets and 510 hosts are available. 10. The directed broadcast should reach all Hosts on the intended network (or subnet, if sub netted). For example, the directed broadcast address for an IP network 196.233.24.15 with default subnet mask is 196.233.24.255. This is arrived by putting all 1s for the host potion of the IP address.