CCNA3 Final - March 2010 #1

1
Which value determines if a switch becomes the central point of reference in the spanning tree topology?
lowest bridge ID
highest revision number
lowest numeric IP address
highest numeric MAC address
2
Refer to the exhibit. What is the purpose of the configuration commands that are shown?
to activate port Fa0/10
to make the port a member of VLAN 30
to activate port security on port Fa0/10
to add VLAN 30 to the trunk that is connected to port Fa0/10
3
Refer to the exhibit. What would happen if the network administrator moved the network cable of Host A from interface Fa0/1 to Fa0/switch SW1?
Host A remains a member of VLAN 10, because the router is routing traffic between VLANs.
Host A is no longer a member of VLAN 10, because port Fa0/3 has been manually assigned to VLAN 30.
Host A remains a member of VLAN 10, because the switch provides dynamic VLAN assignment for the port.
Host A maintains connectivity to all members of VLAN 10, because it is connected to the same physical network.
Host A is no longer a member of VLAN 10, but because port Fa0/3 was unused, it is now a member of VLAN 1.


4
Which device or devices should have the Spanning Tree Protocol enabled to prevent host traffic from creating a broadcast storm?
Core_S1
Access_S2 and Access_S3
Core_S1, Access_S2, and Access_S3
Core_S1, Access_S2, Access_S3, and R1
5
Refer to the exhibit. The hosts connected to switch SW1 are not able to communicate with the hosts in the same VLANs connected switch SW2. What should be done to fix the problem?
Configure VLANs with different VLAN IDs on switch SW2.
Reconfigure the trunk port on switch SW2 with static trunk configuration.
Introduce a Layer 3 device or a switch with Layer 3 capability in the topology.
Apply IP addresses that are in the same subnet to the interfaces used to connect SW1 and SW2.
6

Refer to the exhibit. The Layer 2 switching design that is shown has been implemented in a campus environment that is using Spanning
Tree Protocol. All inter-switch links that are shown are trunks. Whenever an inter-switch link fails, the network takes nearly a minute completely converge. How can the convergence time be reduced?
Increase the capacity of the distribution and core trunk links to 10 Gb/s.
Add a trunk link that directly connects D1 and D2.
Use Layer 3 switching on the core switch.
Implement Rapid Spanning Tree Protocol.

7
What will be the effect of the command S1# copy system:running-config tftp://172.16.2.155/tokyo-config?
The IOS will be copied to the TFTP server.
The configuration file named tokyo-config will overwrite the startup configuration file on S1.
The running configuration file on S1 will be saved via TFTP to a file named tokyo-config.
The contents of NVRAM on S1 will become the startup configuration file on the tokyo switch.
8
Refer to the exhibit. What does the term DYNAMIC indicate in the output that is shown?
This entry can only be removed from the MAC address table by a network administrator.
When forwarding a frame to the device with address 0060.5c5b.cd23, the switch does not have to perform a lookup to determine
the final destination port.
Only the device with MAC address 0060.5c5b.cd23 will be allowed to connect to port Fa0/18.
The switch learned this MAC address from the source address in a frame received on Fa0/18.

9
Which two statements are correct about wireless infrastructure components? (Choose two.)
An AP converts the TCP/IP data packets from their 802.11 frame encapsulation format to the 802.3 Ethernet frame format on the
wired Ethernet network.
A wireless AP does not require any physical connection to allow wireless clients to access the Internet.
An AP is a layer 2 device, similar to a switch, that provides dedicated bandwidth to each connected wireless host.
Collisions do not occur between wireless NICs and APs.
The wireless router performs the roles of AP and router.

10

Which service should be disabled on a Cisco switch or router to prevent packet sniffers from capturing information about the device?
SSH
VTP
CDP
SNMP