CCNA3 Final - March 2010 #2

11
Refer to the exhibit. Hosts A and B, connected to hub HB1, attempt to transmit a frame at the same time but a collision occurs. Which
hosts will receive the collision jamming signal?
only hosts A and B
only hosts A, B, and C
only hosts A, B, C, and D
only hosts A, B, C, and E
12
What are three benefits of employing a hierarchical network design? (Choose three.)
Hierarchically designed networks can more easily be expanded to suit future needs.
Hierarchical design models enhance existing bandwidth through the use of link aggregation.
The hierarchical model allows for specialized functionality at each layer, simplifying device management.Use of a hierarchical design allows replacement of redundant devices with high-capacity network equipment.
A hierarchical design uses firewalls instead of complicated port-based and distribution layer security policies.
The hierarchical model allows the use of high-performance switches at all design layers, thus allowing for a fully-meshed topology.

13
A network administrator implements inter-VLAN routing by configuring subinterfaces on a router. What is one important fact that must considered?
The physical interface must have an IP address configured.
The subinterface numbers must match the VLAN ID number.
The no shutdown command must be issued on each subinterface.
The IP address of each router subinterface must be used as the default gateway for hosts on the corresponding VLAN.
14
Which type of frame contains information that is used in the election of the spanning tree root bridge?
BID
LSA
LSU
BPDU

15
Refer to the exhibit. Each switch is shown with its MAC address. Which switch will be elected as the spanning-tree root bridge if the
switches are configured with their default priority values?
switch A
switch B
switch C
switch D
switch E
switch F
Close Window
Assessment System
1. Assessment Selection 2. Assessment Settings 3. Take Assessment
Take Assessment - ESwitching Final Exam - CCNA Exploration: LAN Switching and
Wireless (Version 4.0)
Time Remaining:
16

Refer to the exhibit. What will happen when frames with a source address other than 0019.d2e4.d9f7 enters interface Fa0/24?
Fa0/24 will become error-disabled.
The incoming frames will be dropped.
The Fa0/24 port LED will be turned off.
The security violation count will be incremented.

17

Refer to the exhibit. The network administrator has just added VLAN 50 to Switch1 and Switch2. Hosts A, B, C, and D are correctly
configured with IP addresses in the subnet range for VLAN 50. Host A can communicate with host B, but cannot communicate with C or host D. What is the cause of this problem?
There is a native VLAN mismatch.
The Fa0/11 interface of Switch1 is not configured as a trunk.
The link between Switch1 and Switch2 is up but not trunked.
VLAN 50 is not allowed on the trunk link between Switch1 and Switch2.

18
Refer to the exhibit. A network administrator enters the displayed commands to configure VLAN 30. What is the result of running these
commands?
VLAN 30 will be added to S1, S2, and S3, but not to S4.
VLAN 30 will be pruned from the VLAN database of S3.
VLAN 30 will be added to the VLAN database of S3 but will not be propagated to S4, S2 or S1.
VLAN 30 will not be added to the VLAN database of S3 and an error message will be displayed.

19
Refer to the exhibit. R1 is configured for traditional inter-VLAN routing. R1 can ping computer 3 but cannot ping computer 1. What is possible cause for this failure?
S1 port Fa0/11 is in the wrong VLAN.
R1 does not have an active routing protocol.
The IP address of computer 1 is in the wrong logical network.
Router interface Fa0/0 has the wrong trunk encapsulation type configured.

20
Refer to the exhibit. How does SW1 manage traffic coming from Host A?
SW1 drops the traffic because it is untagged.
SW1 leaves the traffic untagged and forwards it over the trunk.
SW1 tags the traffic with the lowest VLAN ID value and forwards it over the trunk link.
SW1 encapsulates the traffic with 802.1Q encapsulation and forwards it over the trunk link.